Chamber Furnaces with Wire Heating up to 1400 °C

N 1000 N 1680/S for long parts

N 4550/S

Chamber furnace with fiber insulation for shorter cycle times

Charging trolley for N 2200

N 100 - N 2200/14

These high-quality chamber furnaces for firing, sintering and tempering have qualified themselves with the reliability for many years in daily use. Thanks to their five-side heating, the furnaces provide for a very good temperature uniformity. A wide range of additional equipment perfectly adapt these models to the process requirements.

  • Tmax 1300  °C, 1340  °C or 1400  °C
  • Dual shell housing with rear ventilation, provides for low shell temperatures
  • Five-side heating provide for good temperature uniformity
  • Heating elements on support tubes provide for free heat radiation and long service life
  • Controller mounted on furnace door and removable for comfortable operation
  • Air outlet in the ceiling, motor driven exhaust air flap for models from N 440
  • Smoothly adjustable and easy-to-operate air inlet flap or sliding damper
  • Self-supporting and long-life ceiling construction, with bricks laid in arched construction
  • Special door lock for easy handling
  • Multi-layer insulation consisting of lightweight refractory bricks and backed by special fiber insulation
  • Models up to N 300/.. with removable stand
  • Protection of bottom heating and flat stacking surface provided by embedded SiC plate in the floor
  • Defined application within the constraints of the operating instructions
  • NTLog Basic for Nabertherm Controller: Recording of process data with USB-flash drive

Additional equipment

  • Motor driven exhaust air flap for models N 100 - N 300/..
  • Fan system for faster cooling with manual or automatic control
  • Protective gas connection for purging the furnace with non-flammable protective or reaction gases
  • Manual or automatic gas supply systems
  • Fiber insulation for shorter cycle times, especially cooling periods
  • Multi-zone control for optimal temperature uniformity in the work space
  • Over-temperature limiter with adjustable cutout temperature for thermal protection class 2 in accordance with EN 60519-2 as temperature limiter to protect the furnace and load
  • Process control and documentation via VCD software package or Nabertherm Control Center (NCC) for monitoring, documentation and control
ModelTmaxInner dimensions in mmVolumeOuter dimensions in mmHeating
power inElectricalWeight
 °Cwdhin lWDHkW1connection*in kg
N 10013004005304601007201130144093-phase275
N 150130045053059015077011301570113-phase320
N 200130050053072020082011301700153-phase375
N 300130055070078030087013001760203-phase450
N 44013006007501000450100014001830303-phase780
N 660130060011001000660100017501830403-phase950
N 10001300800100012501000139017602000573-phase1800
N 15001300900120014001500149019602150753-phase2500
N 2200130010001400160022001590216023501103-phase3100
            
N 100/H134040053046010076011501440113-phase325
N 150/H134045053059015081011501570153-phase380
N 200/H134050053072020086011501700203-phase430
N 300/H134055070078030091013201760273-phase550
N 440/H13406007501000450100014001830403-phase880
N 660/H134060011001000660100017501830523-phase1080
N 1000/H1340800100012501000139017602000753-phase2320
N 1500/H13409001200140015001490196021501103-phase2700
N 2200/H134010001400160022001590216023501403-phase3600
            
N 100/14140040053046010076011501440153-phase325
N 150/14140045053059015081011501570203-phase380
N 200/14140050053072020086011501700223-phase430
N 300/14140055070078030091013201760303-phase550
N 440/1414006007501000450100014001820403-phase1320
N 660/14140060011001000660100017501820573-phase1560
N 1000/141400800100012501000139017602000753-phase2500
N 1500/1414009001200140015001490196021501103-phase3000
N 2200/14140010001400160022001590216023501403-phase3900
1Depending on furnace design connected load might be higher *Please see page 77 for more information about supply voltage
catalogue Advanced Materials
(URL: http://333.nabertherm.com/produkte/advancedmaterials/advancedmaterials_englisch.pdf)